pSeries Memory Test

The physical memory resources installed on a pSeries server are allocated to each LPAR on the server based on partition configuration, I/O resources assigned, and applications used. In addition to this, the system firmware will have to be configured with adequate memory resources for initialization and configuration of the server and for supporting the LPARs. Firmware is “software” stored in a memory chip that holds its content without electrical power, such as, for example, read-only memory (ROM), programmable ROM (PROM), erasable programmable ROM (EPROM), electrically erasable programmable ROM (EEPROM), and non-volatile random access memory (non-volatile RAM).

This test captures the memory usage of the system firmware and the physical memory allocations to the LPARs so that, in the event of a memory contention, administrators are enabled to determine what could be causing the contention - is it because the system firmware has not been configured with adequate memory resources, or is it because sufficient memory has not been allocated to the partitions.

Target of the test : An IBM pSeries server

Agent deploying the test : A remote agent

Outputs of the test : One set of results for the IBM pSeries server being monitored.

Configurable parameters for the test
Parameter Description

Test period

How often should the test be executed

Host

The IP address of the host for which this test is to be configured.

Port

Indicate the port at which the specified Host listens. By default, this is NULL.

Real ServerName

Specify the name of the pSeries server in the Real ServerName text box. If the target pSeries server has been auto-discovered using HMC, the server name will be set automatically in the Real ServerName text box. However, while configuring this test for a pSeries server that has been manually added, you have to explicitly provide the server name in the Real ServerName text box.

Note:

To obtain the real server name, a user can login to the target pSeries server as a valid pSeries user, go to the shell prompt of the server, and execute the following command: lssyscfg - r sys -F name

Is Managed By

By selecting an option from the Is Managed By list, indicate whether the target pSeries server is managed using an HMC server or an IVM (Integrated Virtual Manager) server. If the target server has been auto-discovered via an HMC server, the HMC option will be automatically chosen from this list.

Management Server, Management User, Management Password

This test connects to an HMC/IVM server to perform LPAR discovery and to collect host-level and "outside view" metrics from the pSeries server. To enable this communication, first, provide the IP address/host name of the HMC/IVM server in the Management Server text box. If the eG manager had automatically discovered the target pSeries server by connecting to an HMC server in the environment, then, the IP address/host name and user credentials pertaining to that HMC server will be automatically displayed in the Management Server, Management User, and Management Password text boxes.

However, if the pSeries server being monitored was manually added to the eG Enterprise system (and not auto-discovered via the HMC server), then, you will have to explicitly indicate whether the target pSeries server is managed by an HMC server or an IVM server by selecting an option from the Is Managed By list. If the HMC option is chosen, then, you will have to provide the IP address of the HMC server that manages the target pSeries server in the Management Server text box. In such a case, in the Management User and Management Password text boxes, you will have to provide the credentials of an HMC user who is assigned the hmcviewer role.

On the other hand, if the IVM option is chosen from the Is Managed By list, it implies that the IP address/host name and user credentials pertaining to that IVM server has to be explicitly provided in the Management Server, Management User, and Management Password text boxes.

Confirm Password

Confirm the HMC Password by retyping it here

Domain

Set the Domain parameter to none.

SSL

By default, the HMC/IVM server (as the case may be) is not SSL-enabled. This indicates that by default, the eG agent communicates with the HMC/IVM server using HTTP. Accordingly, the SSL flag is set to No by default. If you configure the HMC/IVM server to use SSL, then make sure that the SSL flag is set to Yes, so that the eG agent communicates with the HMC/IVM server using HTTPS.

High Security

In highly secure environments, eG Enterprise could not perform agentless monitoring on the pSeries server using SSH. To enable monitoring of the target pSeries host in such environments, eG Enterprise offers the High Security flag. Setting this flag to Yes indicates that eG Enterprise will connect to the target pSeries server in a more secure way and collect performance metrics. However, you can set this flag to No if the target environment is not highly secured.

Detailed Diagnosis

To make diagnosis more efficient and accurate, the eG Enterprise embeds an optional detailed diagnostic capability. With this capability, the eG agents can be configured to run detailed, more elaborate tests as and when specific problems are detected. To enable the detailed diagnosis capability of this test for a particular server, choose the On option. To disable the capability, click on the Off option.

The option to selectively enable/disable the detailed diagnosis capability will be available only if the following conditions are fulfilled:

  • The eG manager license should allow the detailed diagnosis capability
  • Both the normal and abnormal frequencies configured for the detailed diagnosis measures should not be 0.
Measurements made by the test
Measurement Description Measurement Unit Interpretation

Installed system memory

Indicates the total amount of memory (in MB) installed on the managed system.

MB

 

System firmware memory

Indicates the amount of memory configured for the system firmware (i.e., the hypervisor).

MB

The amount of memory that is required by the server firmware varies according to several factors. Factors influencing server firmware memory requirements include:

  • Number of logical partitions;
  • Partition environments of the logical partitions;
  • Number of physical and virtual I/O devices used by the logical partitions;
  • Maximum memory values given to the logical partitions;

Generally, you can estimate the amount of memory that is required by server firmware to be approximately eight percent of the system installed memory. The actual amount that is required will generally be less than eight percent. However, there are some server models that require an absolute minimum amount of memory for server firmware, regardless of the previously mentioned considerations.

In the absence of adequate memory, the firmware may not be able to support LPAR operations, and may even bring the server down.

Unallocated system memory

Indicates the amount of physical memory that is yet to be allocated to the LPARs.

 

 

System memory used by LPAR

Indicates the amount of physical memory that has been allocated to the LPARs.

MB

Memory requirements for partitions depend on partition configuration, I/O resources assigned, and applications used. Memory can be assigned in increments of 16 MB, 32 MB, 64 MB, 128 MB, and 256 MB. The default memory block size varies according to the amount of configurable memory in the system. The detailed diagnosis of this measure reveals the minimum and maximum memory configurations of each LPAR on the server, and also the amount of memory that each LPAR is entitled to receive (i.e., current memory). With the help of this information, you can quickly isolate those LPARs that may have been under-sized or over-sized in terms of memory resource allocations.

Utilized system memory

Indicates the percentage of physical memory that has been allocated to the LPARs.

 

Percent

Memory requirements for partitions depend on partition configuration, I/O resources assigned, and applications used. Memory can be assigned in increments of 16 MB, 32 MB, 64 MB, 128 MB, and 256 MB. The default memory block size varies according to the amount of configurable memory in the system.

Used the detailed diagnosis of the System memory used by LPAR measure to figure out to which LPAR memory has been improperly allocated.

Figure 1 : The detailed diagnosis of the System memory used by LPAR measure