CBR Application Traffic Test

The real test of the efficiency and overall health of the branch repeater lies in its ability to accelerate application accesses over the wide area network. If the Citrix Branch Repeater is not configured with the right service class policies, QoS thresholds, or compression rules, slowdowns during application accesses will become inevitable! If this is to be avoided, then administrators must keep an eye on every application link managed by the branch repeater, quickly identify links that are handling more or less data than their capacity, and proceed to fine-tune traffic rules over that link via the branch repeater to ensure optimum performance. This is where the CBR Application Traffic test helps. For every application link, this test reports the speed at which the link receives and transmits data and packets, thus measuring how well the branch repeater is managing the traffic over the link and pointing to those links that may require traffic optimizations.

Target of the test : A Citrix Branch Repeater

Agent deploying the test : An external agent

Outputs of the test : One set of results for application link handled by the Citrix Branch Repeater being monitored.

Configurable parameters for the test
Parameter	Description
Test Period	How often should the test be executed.
Host	The IP address of the host for which this test is to be configured.
Port	Refers to the port at which the specified host listens to. By default, this will be NULL.
SNMPPort	The port at which the monitored target exposes its SNMP MIB; The default value is 161.
SNMPVersion	By default, the eG agent supports SNMP version 1. Accordingly, the default selection in the SNMPversion list is v1. However, if a different SNMP framework is in use in your environment, say SNMP v2 or v3, then select the corresponding option from this list.
SNMPCommunity	The SNMP community name that the test uses to communicate with the firewall. This parameter is specific to SNMP v1 and v2 only. Therefore, if the SNMPVersion chosen is v3, then this parameter will not appear.
UserName	This parameter appears only when v3 is selected as the SNMPVersion. SNMP version 3 (SNMPv3) is an extensible SNMP Framework which supplements the SNMPv2 Framework, by additionally supporting message security, access control, and remote SNMP configuration capabilities. To extract performance statistics from the MIB using the highly secure SNMP v3 protocol, the eG agent has to be configured with the required access privileges – in other words, the eG agent should connect to the MIB using the credentials of a user with access permissions to be MIB. Therefore, specify the name of such a user against this parameter.
Context	This parameter appears only when v3 is selected as the SNMPVersion. An SNMP context is a collection of management information accessible by an SNMP entity. An item of management information may exist in more than one context and an SNMP entity potentially has access to many contexts. A context is identified by the SNMPEngineID value of the entity hosting the management information (also called a contextEngineID) and a context name that identifies the specific context (also called a contextName). If the Username provided is associated with a context name, then the eG agent will be able to poll the MIB and collect metrics only if it is configured with the context name as well. In such cases therefore, specify the context name of the Username in the Context text box. By default, this parameter is set to none.
AuthPass	Specify the password that corresponds to the above-mentioned Username. This parameter once again appears only if the SNMPversion selected is v3.
Confirm Password	Confirm the AuthPass by retyping it here.
AuthType	This parameter too appears only if v3 is selected as the SNMPversion. From the AuthType list box, choose the authentication algorithm using which SNMP v3 converts the specified username and password into a 32-bit format to ensure security of SNMP transactions. You can choose between the following options: MD5 - Message Digest Algorithm SHA - Secure Hash Algorithm SHA224 - Secure Hash Algorithm 224 bit SHA256 - Secure Hash Algorithm 256 bit SHA384 - Secure Hash Algorithm 384 bit SHA512 - Secure Hash Algorithm 512 bit
EncryptFlag	This flag appears only when v3 is selected as the SNMPversion. By default, the eG agent does not encrypt SNMP requests. Accordingly, the this flag is set to No by default. To ensure that SNMP requests sent by the eG agent are encrypted, select the Yes option.
EncryptType	If the EncryptFlag is set to Yes, then you will have to mention the encryption type by selecting an option from the EncryptType list. SNMP v3 supports the following encryption types: DES - Data Encryption Standard 3DES - Triple Data Encryption Standard AES - Advanced Encryption Standard AES128 - Advanced Encryption Standard 128 bit AES192 - Advanced Encryption Standard 192 bit AES256 - Advanced Encryption Standard 256 bit
EncryptPassword	Specify the encryption password here.
Confirm Password	Confirm the encryption password by retyping it here.
Timeout	Specify the duration (in seconds) within which the SNMP query executed by this test should time out in this text box. The default is 10 seconds.
Data Over TCP	By default, in an IT environment, all data transmission occurs over UDP. Some environments however, may be specifically configured to offload a fraction of the data traffic – for instance, certain types of data traffic or traffic pertaining to specific components – to other protocols like TCP, so as to prevent UDP overloads. In such environments, you can instruct the eG agent to conduct the SNMP data traffic related to the monitored target over TCP (and not UDP). For this, set this flag to Yes. By default, this flag is set to No.
EngineID	This parameter appears only when v3 is selected as the SNMPVersion. Sometimes, the test may not report metrics when AES192 or AES256 is chosen as the Encryption type. To ensure that the test report metrics consistently, administrators need to set this flag to Yes. By default, this parameter is set to No.

Measurements made by the test
Measurement	Description	Measurement Unit	Interpretation
Data transmitted	Indicates the rate at which data was sent over this application link.	KB/Sec	WAN links have low bandwidth when compared to LAN links. Moreover, any attempt made to send or receive traffic faster than the link throughput can result in congestion. Therefore, the branch repeater should make sure that just about enough data is sent and received over application links to prevent congestion and optimize throughput. If the values of these measures exceed or are dangerously close to the bandwidth limit of the link, it signals a potential congestion or slowdown of traffic over the link. It also indicates that you may have to reconfigure the branch repeater with more robust QoS and compression rules to prevent such unpleasant eventualities.
Data received	Indicates the rate at which data was received over this application link.	KB/Sec
Packets transmitted	Indicates the number of packets transmitted over this application link.	Number	WAN links have low bandwidth when compared to LAN links. Moreover, any attempt made to send or receive traffic faster than the link throughput can result in congestion. Therefore, the branch repeater should make sure that just about enough data packets are sent and received over application links to prevent congestion and maximize throughput. If the values of these measures exceed or are dangerously close to the maximum number of data packets that the link can handle, it signals a potential congestion or slowdown of traffic over the link. It also indicates that you may have to reconfigure the branch repeater with more robust QoS and compression rules to prevent such unpleasant eventualities.
Packets received	Indicates the number of packets received over this application link.	Number
Data dropped during transmission	Indicates the rate of traffic not sent over this application link due to QoS threshold settings.	KB/Sec	QoS (quality-of-service) is a set of policies and priorities assigned to the application traffic prioritized under traffic shaping policies in BR devices. A QoS threshold allows a sender to deliver only as much data as the branch repeater allows it to send, and this data is placed on the link at exactly the right rate to keep the link full but not overflowing. By eliminating excess data, the branch repeater is not forced to discard it. Without the branch repeater, the dropped data would have to be sent again, causing delay. A high value for these measures could therefore indicate one of the following: The link bandwidth is low and hence the branch repeater has been rightly configured with a QoS threshold that allows only limited data to be sent/received over that link; this excludes a lot of data from transmissions/receptions and maximizes the responsiveness of the link; The branch repeater has been misconfigured with a QoS threshold that forces the link to send/receive much less data than what it can handle; this causes a lot of data to be unnecessarily dropped from transmissions/receptions, affecting the quality-of-experience in the process. In this case, you may have to fine-tune the QoS policy.
Data dropped during reception	Indicates the rate of traffic not received over this application link due to QoS threshold settings.	KB/Sec
Packets dropped during transmission	Indicates the number of packets not sent over this application link due to QoS threshold settings.	Number	QoS (quality-of-service) is a set of policies and priorities assigned to the application traffic prioritized under traffic shaping policies in BR devices. A QoS threshold allows a sender to deliver only as much data as the branch repeater allows it to send, and this data is placed on the link at exactly the right rate to keep the link full but not overflowing. By eliminating excess data, the branch repeater is not forced to discard it. Without the branch repeater, the dropped data would have to be sent again, causing delay. A high value of this measure could therefore indicate one of the following: The link bandwidth is low and hence the branch repeater has been rightly configured with a QoS threshold that allows only limited number of packets to be sent/received over that link; this excludes a lot of packets from transmissions/receptions and maximizes the responsiveness of the link; The branch repeater has been misconfigured with a QoS threshold that forces the link to send/receive much less data than what it can handle; this causes a lot of packets to be unnecessarily dropped from transmissions/receptions, affecting the quality-of-experience in the process. In this case, you may have to fine-tune the QoS policy.
Packets dropped during reception	Indicates the number of packets not received over this application link due to QoS threshold settings.	Number